Monday, June 29, 2009

VHF Preamplifier


....Here is the infamous VHF preamplifier that let me discover the problem in the antenna input plug, no wonder it worked better with the antenna cable in short circuit that with it open, the external cable was really working as the antenna.

Now it works nice, at least improves something on the signal level, without the amplifier I have for instance S4, with the amplifier goes to S5, not bad but not great either...could be good for marginal signals.


You probably can use the orignal design, I started testing with the coils but then remove them until I found the problem was the antenna input. Mine is working like on the schematic... less is more :)

Now the airband receiver continues to not working well, will buy another TDA1072 to check it it's broken.

Sunday, June 28, 2009

New airband input filter part (II)

...It's probable that the filter and amplifier are working... today I was brewing another pre amplifier and after much testing and not understating why a piece of wire working as an antenna was working better than the external antenna I found the plug from the cable of the external aerial was broken.... I don't feel like to talk more on this subject....

p.s. It's quite probable that the "broken" TDA1072 was also related to this plug "problem".

Saturday, June 27, 2009

New airband input filter

New filter...new problems....

Built the filter in this schematic:


































"My" filter stops after C8 and without R6 and C9, basically everything that is connected until the 2SC transistor.

After making the coils and soldering everything.... power to the circuit. Input connected to my airband antenna and output (right end of C8) connected to my TM-D700.... it went from an amplifier to and attenuator... before the filter insertion I had S2 on a continuous transmission frequency, now I barely can hear the transmission.....could be the coils... made a new set and solder them.... a litle beter but no increase in signal, only S0! Tryed some varicaps in paralel with the 82p capacitors some triming and nothing.... could be the transistor..but it's brand new and was tested in my multimeter....
Next time i will probably test every tuned circuit agains the antenna analyser, that way will have a beter idea of how far I am from expected ressonance frequency.

RF is fun.... the emiter terminal of the 2sc transistor is about 1cm long, is connected to the ground but if I placed an trimer capacitor bettwen ground and 3mm of the lenght of the terminal (from ground) there is some notiçable change in sound from the receiver......oh well, giving up for the weekend...probably not.

Thursday, June 25, 2009

Airband receiver...the saga

Yup....I think I broke an TDA1072 (AM demodulator et all). Trying to improve sensitivity on the airband receiver decided to try the NE602 as a front end... some soldering later (I never had tested the Si570 connected to the NE602) it was ready to rock....powering up and some hash sound (noise) changed "vfo" to the local FM station....and nothing...just before I notice the s-meter geting a litle higher than usual....normaly is a good sign, more IF, more signal... but nothing other than noise, time to check connections.... everything was alright except I forgot to solder one of the NE602 pins... soldered and nothing... some more tests and nothing.... you can imagine the rest... testing...soldering loop...
Ok the NE602 is not as easy as that, at least with the TDA IF, let's connect again with the TA7358.... now a circuit that was working is not any more and since the common part in the equation was the TDA1072 I assume it is broke or at least part of it... had no more patience for the day so I will leave it for further testing.

Anyhow, found a nice airband filter for a NE602 front end an probably will use part of it to connect the TA7358 maybe will improve things a little better.

Bought 2 MC3361 for making an FM IF, at least part of the airband schematic will be used if not for AM at least for FM.

Also going to make a small DC receiver, crystal controlled on 10.7Mhz so I can verify the 10.7 IF output, unfortunatly my scope is broken so other testing equipment has to be made to get more info.

Tuesday, June 23, 2009

The airband receiver squelch revisited

....Impossibly to find a stand alone (and simple) squelch in the internet and in books that I have.

Had to cut and past from a bigger online receiver design and rework some changes.
Since last time I studied op-amps somewhere last century I forgot that ideal op-amps are not real ones, that's why there are so many models. The original design (first rework) was not working due the specific nature of "real" op-amps... the 741 didn't worked as expected.

It's a simple comparator circuit without hysteresis.... that is done by the lack of precision of the adjustable potentiometer movement (backslash et all), if it was a multiturn, probably hysteresis was a good thing to have.

The schematic:




















There is space for improvement, for instance if the signal is to strong it will not block the audio (max signal value no enough), changing the 1k ohm resistor for a bigger value will allow that, in the other hand it is nice if your friend is calling you on frequency near your house....

And the video of it working (not a very explicit example since exactly when I was testing all the channels were with signals opening the squelch level I set):


0-500 Khz converter to 4Mhz


No big science here, the venerable NE602 working as a mixer....again...
This was part of a NAVTEX receiver experiment. NAVTEX signals are around 490 and 518 Khz so I first built an PLL oscilator for those frequencies (for a DC receiver) but the PLL never worked like I wished so the idea was first to make the conversion to 4Mhz and then built a direct receiver around that frequency. Never did built the receiver but tested the converter against my TS-50 and it did received great.
The PCB schematic is not exactly the same in the paper (different input filter) but any design with the NE602 will work.

Monday, June 22, 2009

Read the datasheet

Why am I writing this... because my aviation band receiver was not receiving what I wanted, only some aircraft's passing by, nice music on 88-108, some packet on 144.800 but I couldn't get VOLMET (meteo info) on 126.400 but my TM-D700 could receive on the same place and with an inferior antenna (it's bad when your own homebrew receiver is inferior to a commercial unit that took years to develop....)

I allways say: "RFTM" (read the friendly manual)......but never do it myself :)

After testing numerous TA7358 schematic configurations I found on the internet, finally decided to look carefully at the IC datasheet and go some conclusions:

"Wide supply voltage range: Vcc = 1.6-6v": some schematics have a Vcc of 8 or 9V ??? IC max supply at 25ºC is 8V .I tested to 12v....it survived ,Inow set it to 6V

Look at the schematic in the datasheet and you will see a tuned circuit at pin 3 (rf amp out): Some shcematics don't have a "by the book" tuned circuit...have something else...my circuit now has one and the internal rf amp is "tuned" and tunable. Removed the external rf preamp since there is no need of a rf preamp connected to pin 1 (rf preamp in), just a bandpass filter. If you put a preamp before it will overload the poor IC expecialy in hurban environment

After some testing and configuration change on the TA7358 I now can receiver VOLMET, with some noise in the background but readable, now it's time to improve even further...

I found out that if you trow a TA7358 to a PCB it will work, limited but will work, but if you whant to get all the juice from it you have to push hard and test a lot... will post some more news later.

If you copied my receiver schematic you will have a limited performance.. I told you so...never trust an internet schematic...

....and the squelch design is also broken... also working on a new one (my own design).

No photo today! Read!