Tuesday, January 05, 2010

S9 signal generator


....I just knew it was to easy (on the online pdf) to be true....
When you finish soldering and go for a test then it's when the s!"#!" hits the fan...

I was looking for a test generator to start testing MDS on my new hf-radio (somewere on this blog). I could just get my cristal tester and place some attenuators, but no, I had to look for a specific schematic.... guess what, Elecraft make's a nice little kit, the XG2, (http://www.elecraft.com/manual/E740084%20XG2%20Manual%20Rev%20E.pdf).... I am sure them works... not my homebrew copy... I didn't had the reference regulator in the schematic so I replaced for a 1.5 Volt's battery removing the left part of the schematic (the 3v battery). I had heard that is not easy to make low voltage oscillators, mine didn't worked has in the original Elecraft schematic so I made some small changes. It could had been the type of crystals or any other thing but in fact I could just make the circuit start oscillating at around 2.8V
My schematic:















Anyhow the main output gives around S9+5 on my Yaesu FT-102 and around the same on the Kenwood TS-50.
I have some leakge from the attenuator so on 1uV setting I have around S5. Am now in the process off making a 34db (will probably make a 40db) attenuator with some blindage to try to get the S1 level. Will try an online attenuator tool: http://www.g4nsj.co.uk/attenuators.shtml
I didn't had the crystal frequencies specified on the schematic so I used for now 10Mhz and 4Mhz. At least with the 10Mhz I can test on the Yaesu, Kenwood and my new radio for comparation.

The box was from a previous PSK/RTTY interface, and no it's not a wine or wisky box, it's from a perfume. Cheap and easy.


addendum:
Added a 40db attenuator (2 times 51 ohm and 2.5Kohm PI)and now have more or less S0 (can't measure level). Can't listen to it on the FT-102 without preamp (to FT-102 favor, there is a birdie at 10Mhz that overlaps). Can listen to this low level on the TS-50 (IPO in and out). On my homebrew radio.....well.....I can listen! Very, very faint but I have no preamp at the moment!

Wednesday, December 30, 2009

The box for the hf-radio

Not much text here and especially none schematic!













There's a lot of stuff still missing in the receiver part.

- A better working AGC, have to check schematic again.
- Tone control
- Pot for volume control
- All the bandpass filters
- Pre-amp
- Attenuator
- Connect the mode selector (second bigger knob on the panel)
- Power supply switching for rx/tx
- Fine tuning the audio notch
- Add a variable filter....includes changing all the IF part....
- Other stuff missing....

In the future will post all the schematic. now, it's like this:

Input filter: will be from the GQRP design of bandpass filter
RF preamp: will be from K2
Front end mixer: From the ARRL 14Mhz receiver
First amp: From 14mhz receiver but will put equal to the K2 transceiver
IF amp: from ARRL receiver but output is equal to MC1350 datasheet
BFO mixer: ARRL...
BFO oscilator: From Minipig receiver
Audio amp: ARRL...
Notch filter: From QST design
Audio amp: ARRL...
VFO: Hands electronics DDS-3
VFO amp: Can't recall now...

Happy new year!

Tuesday, December 29, 2009

140Km/h antenna


This month, on the 23, my family QTH area sufered from a small winter storm.
I don't have a real shack there, just a small marine band receiver and a homebrew VHF antenna based on the design somewere on this blog (http://speakyssb.blogspot.com/2008/06/vhf-antenna-another-one.html)
The small antenna survived 140Km/h peak and 80Km/h average winds recorded by a nearby navy weather station.
The satelite image is at the time of the storm pass.

There were a lot of damage in the area including some roofs that disapered and around 20 very high voltage electricity poles (10 tons each) putted to ground, luckily there were no personal injuries.

Will put later on the antenna images.

Wednesday, December 23, 2009

Power meter IC arrives

Got this in the mail:












Sorry for the crap photo...I do solder better :)

Santa did come early this year and brought me an AD8307.
Since I will be busy with other stuff probably will only make the power meter latter on. Will also use the Linear IC for a full DC to dayligh power meter.

Meanwhile I've been searching for a nice tone control to place on the hf-radio and that will be the next thing to put there. The AGC is ready but I still have to put the TL074 on the IC socket , there is no LM324 in town so the TL074 will fit nice, I hope!
Also changed a litle bit on the IF amplifier part and the output of the MC1350 is now acording to fig 7 on his datasheet, the values I placed were for 10.7Mhz but looks like it is working whit less noise... probably will change the input part also.

Monday, December 21, 2009

HF radio (5)

Had some time to improve the radio a little bit and added a notch audio filter. Had to change the opamp since it is hard to find the RC4134 so made the lucky guess of replacing it by an TL074.
















This notch is not bad considering I didn't matched the resistors nor the capacitors....it goes almost from 0 to 7Khz, will change that latter on, I only need to go to 3Khz.

After seeing the images on the computer I discovered the I have an audio bandwith of 7Khz.... as you can see in this photo (the notch is around 3.5Khz)
The signal you see at around 1.5Khz is from an transmission that was on 10.100Mhz and is were I make the air tests since it sits almos all day there and has a big signal.














what's is the cristal filter doing? The problem is not the cristal filter but noise induced by the MC1350 (I think). Probably will upgrade the schematic to look like the Elecraft K2 in wich they have a small cristall filter after the MC1350.... now I understand why they placed it there.

Here is an output of my TS-50 appliance...see the cut at about 2.5Khz?
















On the radio, I placed a LSB/USB selector based on a diode switcher and changed the feedback capacitor on the oscilator because it was not starting all the time, the oscilator itself changed from a double 2n3904 to an 3904/06 pair similar to the minipig-10 transceiver bfo (the one at 8.064Mhz), just removed L20,L21 and C57. Didn't used for now the diode switching part after the vfo.
Here is how the board looks now, there is already in place the AGC IC support near the cristal filter... that will be made another day:











Top row from left to right: Notch filter, BFO oscillator, AGC IC support and bellow cristal filter, VFO buffer.
Bottom row from left to righ: Audio amp, audio pre-amp, BFO mixer (SBL-1), IF amp (MC1350), relay cristal filter switch, first mixer amp, first mixer (SBL-1).


Last minute update: I got one LTC5507 hopping to make a power meter that goes to Ghz....(I allready bough an AD8307 but waiting for it's arrival) problem is I had no idea how small the component is... anyhow will make the power meter if I can find a soldering needle.. the IC it self is the same size as the pen tip....the same size as an SMD resistor... and has 6 terminals!!!!


















Season greetings....

Wednesday, December 16, 2009

Meter repair



Some years ago I grabbed my tent and went to Germany to the ham radio exhibition. The idea was to leave the tent and on the spare space bring a lot of junk.
I did managed to bring the tent and the junk... although at the Swiss airport (I went via Zurich) control was difficult to put everything inside after removing the tent to explain what was that on the x-ray..... they weren't interested in the wires, valves, meters, etc... oh well.
Unfortunately 2 of the meter I bough were damaged... can't trust some sellers.. today I did managed to repair one, some soldering's and voila... some one had already tried but without success since some nut's were inside wrapped in paper. The other metter was a Russiam metter and the moving coil was in open state...so almost impossible to repair, will keep the magnet.



The idea was to use the meter in my future rf power meter but honestly it is to big for finding a nice box. Will be used in some other project. This meter must had come from a "m Ohm" meter, don't need one for the moment but let me think that it must had used a Wheatstone bridge or something similer for measuring.

I have one 150uA meter from the "Westinghouse Electric Company" and probably will be the one to use, after all "Mr Westinghouse" was a defendant of the "Alternate Current" although for some more "dBm" that I intent to measure....

Monday, December 14, 2009

HF radio (4)

...The first sound.... not quiet what I was expecting but already some reception. The radio is a little deaf (no rf preamp and no rf input filter at this moment).
Made some more tests after this video, changed the first if preamp schematic a little bit but not much improvement, still have to check levels on sbl-1 mixers and verify all the if gain part of the cristal filter and mc1350. Basically at this point is copying equivalent to S2/3 on a commercial normal transceiver... I want a little more, also I already verified that the lower the noise the better to distribute the gain so will separate all the oscillators and different modules with some pieces od PCB.




Here's is another video at 20m band. Note that I changed the cristal filter relay in the middle of the board for a smaller one.